Click Logo for Home Page
FactoryLink Drivers


Home | Products | Downloads | Manuals | Prices | Order Info | Register a Product | Support |

>   Allen-Bradley Ethernet  More ..

Allows FactoryLink on Windows NT/2000/XP to communicate with Ethernet connected Allen-Bradley PLC-5/xxEs and SLC-5/05s. This product does not require Allen-Bradley RS-Linx, nor any additional software other than supplied in standard FactoryLink and Windows NT/2000/XP.  Unsolicited message support is provided as well as block read, block write and exception write. Does not support remote/off-link addressing. Does not use the FactoryLink Device Interface Module

>  Allen-Bradley DH/DH+ via SST 5136-SD PCI or ISA Cards  More..

Allows FactoryLink on Windows NT/2000 to communicate with Allen-Bradley Programmable Logic Controllers over either A-B Data Highway or Data Highway+, via the SST 5136-SD PCI or ISA interface cards for either Windows 2000 or Windows NT4. Compatible with PLC-2, PLC-3 (requires SR-5 interface for bit writes), PLC-5, PLC-5/250, & SLC-5/04. Unsolicited message support is provided, using originating PLC's native format. Supports remote/off-link addressing using PLC-5/250 or 1785-KA.  Uses the FactoryLink Device Interface Module Note that ISA-bus cards are not supported under Windows XP

>  GE Fanuc Ethernet   More..

For existing FactoryLink users: Allows FactoryLink on Windows NT/2000/XP to communicate with multiple GE 90-30 and GE 90-70 programmable logic controllers equipped with TCP/IP Ethernet Interface Modules, over industry standard TCP/IP LANs and WANs. Uses the FactoryLink Device Interface Module.

>  GE Fanuc SNPX Serial  More..

For existing FactoryLink users: Allows FactoryLink on Windows NT/2000 to communicate with multiple GE 90-30 and GE 90-70 programmable logic controllers. Uses standard COM1 and/or COM2 serial ports to communicate with either single or multi-dropped PLCs via the built-in RS-485 SNPX port on the PLC. This provides cost-effective communication with single or multiple PLCs located throughout a plant. No extra PCIM or CMM modules are required, and low cost twisted pair wiring can be used. Uses the FactoryLink Device Interface Module.

>  GE Fanuc Genius Bus via PCIM  More..

For existing FactoryLink users: Allows FactoryLink on Windows NT/2000 to read and write data to GE 90-30, GE 90-70, and directly monitor all Genius I/O Block types without a PLC, via 153.6K Genius LAN. The driver provides GCM+ support for 90-30 PLCs. Support for redundant 90-70 control. Unsolicited message support for 90-70 PLCs. Uses the FactoryLink Device Interface Module. Note that ISA-bus cards are not supported under Windows XP

>   Gemlan-D More..

For existing FactoryLink users: Allows FactoryLink on Windows NT/2000 to communicate with ALSTOM PLCs fitted with a GEMLAN-D network interface. GEMLAN-D uses DECnet as the network protocol,  and the driver is highly optimized for read/write throughput. Uses the FactoryLink Device Interface Module.

>  Omron Fins Gateway  More..

Provides communications between FactoryLink on Windows NT/2000 and Omron PLCs using Omron Fins Gateway runtime software. The driver also provides facilities for BCD conversion and for linear scaling on both reads and writes. Uses the FactoryLink Device Interface Module.

>   Square-D SY/LINK  More..

For existing FactoryLink users: Allows FactoryLink on Windows NT/2000 to communicate with Square-D PLCs via a SY/LINK Network Interface Card. Compatible with Square D PLC models: 300, 400, 500, 600, and 700. Communicates over SY/NET LAN (Net-to-Net) with network baud rates up to 500K, or SY/LINK RS-422 port with baud rates up to 19.2K. Uses the FactoryLink Device Interface Module Note that ISA-bus cards are not supported under Windows XP

 

Home | Contact Us | Search |
About Us | Links | Privacy |
Copyrights & Disclaimers |
  © 2001-16 Axisware LLC, Plano, TX, USA. Tel +1 (214) 764 1876.
About this site. All Trademarks are the property of their respective owners.  E&OE.